Will the Anti-Slip Traction Mat for Bathtub and Shower Floors stay put on a wet bathtub?

That is the job — if the surface was actually clean and dry at install. Film under the adhesive is why pieces let go in a week.

Do I need a contractor?

No. Clean, dry, peel, press. If you can hang a shower caddy, you can do this.

Will it wreck the finish?

On a prepped surface it is meant to hold without eating the glaze. Peel slowly if you ever take it off.

In place, with household cleaner and a soft brush. You do not need to remove it for a normal clean.

How much does it cost?

See the current price on the product page from $29.95. Free shipping over $65 on qualifying orders.

Bath and Shower Mats

Anti-Slip Traction Mat for Bathtub and Shower Floors

From $29.95

Choose your options in the store to see current price and availability.

Waterproof adhesive
Barefoot-safe grip
Peel & stick install
Indoor & outdoor

Free shipping over $65Easy returns100% satisfaction guarantee

You'll complete checkout securely on the Kahuna Grip store.

Free US shipping over $65
DIY install in minutes
Grips when wet
Secure checkout

About the Anti-Slip Traction Mat for Bathtub and Shower Floors

Give your bathtub or shower floor a fitted traction surface with the Kahuna Grip peel-and-stick mat. Choose a size and design from the options above; availability and price update with your selection. Choose the right size Available sizes are 14 × 27, 16 × 35, and 26 × 32 inches. Measure the flat area where you plan to place the mat before ordering. Select each size and design to check current stock. Installation and care For adhesion, clean the surface thoroughly to remove soap scum, oil, dirt, wax, and grease. Finish with rubbing alcohol and let the surface dry completely. Position the mat, peel away the adhesive backing, and press it down from the center outward. Hand wash and spot clean as needed. Read the full installation instructions before applying. Questions about sizing or the surface you plan to use? Contact Kahuna Grip before ordering.

Why a wet bathtub still wins

Factory finishes in the bathroom are designed to wipe clean. That same smoothness is why soap and water turn them into a lubricant. You have already felt it — the half-second where the foot goes before you do.

Suction-cup mats hide mildew and let go when the cups fill with film. Coatings wear. The useful fix is texture that stays put on a surface you actually prepped.

What the Anti-Slip Traction Mat for Bathtub and Shower Floors actually does

Put it where the foot lands: the tub step-in, the shower turn, the stair nose, the ramp threshold. Coverage only matters in that zone. A pretty oval in the middle of a tub you never stand in does nothing.

Match the piece to the foot

Barefoot tubs and showers want a fine texture. Outdoor steps and ramps can take a more aggressive grit. Mixing those up is how you get a complaint, not a safer house.

If you are covering a stair, the nose of the tread is the land zone. A full runner is optional. The nose is not.

How to install the Anti-Slip Traction Mat for Bathtub and Shower Floors

Clean until the bathtub is honest, then peel and press. If a previous mat failed, the prep failed first.

1
Empty the tub and look at the glaze
If you see a white haze or a soap ring, that is the bond-killer. You are cleaning that off, not decorating over it.
2
Wash, rinse, then degrease
Household cleaner first. Then rubbing alcohol on a lint-free cloth. The glaze should squeak. If it feels slick, you are not done.
3
Dry it like you mean it
A towel, then five extra minutes. Humid rooms lie about dry. Exhaust fan on.
4
Place before you peel
Dry-fit the Anti-Slip Traction Mat for Bathtub and Shower Floors on the step-in — where the first foot lands — not in the middle of a slope you never stand on.
5
Peel, set, press from the center out
Work out air. Press the edges extra. Stay off it for a few hours if you can so the adhesive can set.

Mistakes that make this fail

Sticking it to soap film
If the bathtub still feels slick after a rinse, you are gluing to lotion. Alcohol wipe until it squeaks.
Covering the wrong zone
The middle of a tub you never stand in is decoration. The step-in, the turn, and the stair nose are the land zones.
Using outdoor grit in a shower
Coarse tape belongs on shoes and weather. Barefoot baths want a fine texture. Mixing those is uncomfortable, not safer.
Walking on it in the first hour
your area heat, cold, and humidity all change set time. Give the adhesive a quiet stretch before the next shower or the next flight of stairs.

Keeping it clean after install

Clean in place. Warm water, a soft brush, and a household cleanser. You do not peel it off for a weekly scrub. Comet or Ajax is what we tell people for the mats.

If a white haze comes back, that is mineral or soap film sitting on the texture. Clean the film. The grit is still there.

If an edge lifts, dry the area, press it back, and keep traffic off. A lifted corner that stays wet is how mildew starts — not a reason to throw the piece away on day three.